Cove Base
Adhesive
Description
HENRY is a high-performance wet-set adhesive for installing
rubber and vinyl cove base
Use For
Commercial and residential installations of rubber and vinyl
cove base.
Bonds To
Structurally sound, clean, smooth, dry wall surfaces. Glazed
or metal surfaces must be abraded. Refer to the cove base
manufacturer’s specific recommendations for suitable
substrates.
Preparation
•Acclimatetheinstallationarea,adhesiveandflooringin
an enclosed building at a minimum of 65°F (18°C) for
at least 48 hours before, during, and for 48 hours after
installation.
•Substratemustbesound,smooth,flat,clean,dryand
free of excess moisture and alkali. Remove dirt, wax,
grease, paints, oils, sealers, curing compounds and all
foreign matter that would interfere with proper adhesion.
Installation
Follow the flooring manufacturer’s guidelines for layout and
design. Stir any liquid found on the surface into the adhesive,
and apply adhesive to the cove base or to the wall using the
proper trowel. Stay 1/8” away from the top and bottom of the
cove base to prevent the adhesive from oozing. Place cove
base into position. Butt the joints neatly. Using a hand roller,
roll toward the previously installed section.
11 oz or 30 oz cartridge Directions:
Packaged in a dual-purpose cartridge for your convenience;
may be applied with standard closed barrel gun or open barrel
skeleton gun.
Closed Barrel Gun: Cut spout about 1/2” from top of tube.
Puncture inner seal. Insert cartridge and attach nozzle. Use
2-hole nozzle for 2-1/2” wall base, 3-hole nozzle for 4” wall
base, and 5-hole nozzle for 6” wall base.
440
HT106 (09/11)
Skeleton Gun: Cut spout near tip to produce 1/8” bead.
Puncture inner seal and insert cartridge. Use two 1/8” beads
for 2-1/2” wall base, 3 beads for 4” wall base and 5 beads for
6” wall base. Be sure to use enough adhesive. Immediately
place wall base and roll toward previously installed section
using a hand roller.
Clean Up
Remove wet adhesive residue with a clean, white cloth
dampened with soapy water. Use mineral spirits for dried
adhesive residue, carefully following warnings on the container.
Warranty
10-Year Limited Warranty. For complete warranty details please
contact our Customer Service Center 1-800-232-4832.
Notes
Do not reuse container. Dispose of container and adhesive
residue in accordance with federal, state and local waste
disposal regulations. Do not flush adhesive down drains.
KEEP OUT OF REACH OF CHILDREN.
•Freeze/thawstableto10°F(-12°C).Avoidlow
temperatures or multiple freeze/thaw cycles.
•Shelflifeisoneyearifunopened.
•VOCcontent:0g/L;calculated&reported,SCAQMD1168
PRECAUTIONS! Maybemildlyirritatingtoeyesandskin.May
causeallergicrespiratoryreaction.Maycauseallergicskin
reaction.
Carefully read and follow all cautions and warnings on label
orrefertoMaterialSafetyDataSheetforallwarningsand
additional product information. ( www.wwhenry.com)
MadeinUSAbyTheW.W.HenryCompany,
Aliquippa, PA 15001
1-800-232-4832
www.wwhenry.com
(1 pages)
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals